SIEMENS
SINAMICS DCM
DC转换器和控制模块
直流转换器
3/50
西门子D 23.1·2014
3
■
更多的information
（继续）
Functions of the inputs and outputs
模拟用户分配的输入
After converting to a digital value, the quantity of the analog
inputs can be flexibly adapted via parameters for scaling, filter,
sign selection and offset input. The values are available as con-
nector. This is the reason that the analog inputs can be effective
作为主要设定值，也是补充的数量
setpoint or a limit.
模拟输出
可选的模拟输出可用于输出模拟
signals. Analog signals can be output as bipolar signal or as
绝对值。在这种情况下，缩放，偏移，极性和
filter time can be parameterized. The required output quantities
通过输入连接器在干预点选择
numbers. For instance, speed actual value, ramp-function
generator output, current setpoint, line supply voltage etc.
可以输出。
二进制输入
•
Switch-on/shutdown (OFF 1)
This terminal function is ANDed with the control bit of the serial
接口。为一个H信号终端
switch-on/shutdown
,
主接触器通过内部序列控制关闭。这
如果操作处有H信号，则启用控制器
使能够terminal. The drive accelerates up to the operating
speed with the speed setpoint. For an L signal at the terminal
switch-on/shutdown
，驱动器逐渐升高
n
<
n
最小
通过坡道功能发电机；制动后
trol delay time, the controllers are inhibited and at
I
= 0, the
main contactor is opened. After this, after an adjustable time
after the main contactor has dropped out, the field current is
降低到停滞场电流（这可以是参数 -
ized). The standstill field can e.g. be used as anti-condensa-
tion heating for the motor; to do this, approximately 30 % of the
rated field current must be entered as standstill field. The mo-
TOR风扇必须为100％的田间运营
rated field current. Otherwise, the field winding will be over-
loaded.
•
操作启用
此函数与串行间的控制位遵守
脸。控制器启用了使用H信号
操作
ating enable
terminal. For an L signal, the controllers are inhib-
it和at
I
= 0，脉冲被抑制。信号
操作
使能够
has a high priority; this means that if the signal (L sig-
nal）在运行中被撤回，然后始终导致
I
= 0
and therefore the drive coasts down.
二进制用户分配输入：
Additional binary input terminals are available for user-assign-
功能功能。在这种情况下，分配了一个分配器编号
every user-assignable terminal, which can be used for control
functions.
二进制输入函数的示例：
•
Voltage disconnect (OFF 2): For OFF 2 (L signal), the control-
lers are instantaneously inhibited, the current in the armature
circuit is reduced and at
I
= 0，主接触器打开。
这drive coasts down uncontrolled.
•
Quick stop (OFF 3): For a quick stop (L signal), the speed set-
指向速度控制器输入设置为零，驱动器
沿当前限制进行刹车以快速停止（parameteriz--
有能力的）。在
n
<
n
最小
after the brake control delay time
I
= 0 is
entered and the main contactor is opened.
•
慢跑：慢跑功能可用于L信号
terminal
switch-on/shutdown
，对于端子上的H信号
操作
ating enable
and when the jogging function is controlled. In
这种情况，主接触器已关闭，驱动器加速器 -
ates到参数中定义的慢跑设定点。什么时候
慢跑信号被撤回，驱动器是刹车到
n
<
n
最小
;
在这之后,抑制和控制器main contactor
在可参数化时间（0至60 s）之后打开。此外，它
can be selected as to whether the ramp-function generator is
active or ramp-up time = ramp-down time = 0 is used.
二进制输出
用户分配的信号传导功能可在二进制中获得
输出终端（开放发射极输出）。任何双层器数量，
which can be selected via the associated user-assignable
parameter, can be output for each terminal. The polarity of the
output signal and an adjustable delay time (0 to 10 s) can be
selected using parameters.
Examples of binary output functions:
•
故障：存在故障消息时输出L信号。
•
n
<
n
最小
: An H signal is output for speeds less than
n
最小
.
This signal is used, for instance, as a zero speed signal.
•
Switch-on command for a mechanical brake: A motor brake
can be controlled using this signal.
什么时候switching on the drive using the "switch-on" function and
entering "operating enable", an H signal is output to open the
brake, in this case, the internal controller enable is delayed by a
可参数的时间（等待机械制动打开
time to expire). When shutting down the drive using the "shut-
down" function or "quick stop", an L signal is output to close the
brake when speed
n
<
n
最小
is reached. At the same time, the
internal controller enable is present for a parameterizable time
（等待机械制动的关闭时间到期）：
I
= 0 is entered, the pulses are inhibited and the main contactor
被打开。
可以使用“关闭”选择其他操作模式
brake" signal (L signal at the binary user-assignable output). As
结果，当存在“内部控制器抑制”时
(the drive is in a no-current condition), the drive does not wait for
状态
n
<
n
最小
, but the brake is already controlled (operating
刹车）的速度大于
n
最小
.
发生故障消息时存在内部控制抑制，
when the voltage is disconnected or the operating enable –
terminal
操作使能够
– is withdrawn in operation.
© Siemens AG 2014