SIEMENS
FLENDER Standard Couplings
Appendix
适合
15/2
Siemens MD 10.1 · 2015
15
■
概述
Fitting recommendations
对于许多应用，拟合分配M6/H7特别合适。
Deviation table to DIN ISO 286 for above-mentioned fits for bore diameters from 10 mm to 250 mm
圆柱轴的末端，从DIN 748第1部分（长）提取
Central holes according to DIN 332 Part 2
描述
Application
轴公差
孔耐受性
Sliding fit with parallel key connection not suitable
用于逆转操作
For steel and cast hubs
j6
H7
h6
J7
Press fit with parallel key connection not suitable for
reversing operation
For steel and cast hubs
h6
K7
k6
H7
Interference fit with parallel key connection suitable
用于逆转操作
For steel and cast hubs
m6
H7
n6
H7
h6
M7
Interference fit with parallel key connection suitable
用于逆转操作
仅适用于钢枢纽
Preferred for ZAPEX and ARPEX coupling series.
h6
P7
k6
M7
m6
K7
n6
J7
p6
H7
s6
F7
Shrink fit connection without parallel key
仅适用于钢枢纽
The permitted hub tension must be urgently checked.
u6
H6
v6
H6
x6
H6
Diameter
无聊
轴
F7
H7
J7
K7
M7
P7
h6
j6
k6
m6
n6
p6
over
to
Deviations in μm
10
18
+34
+18
+10
+6
0
-11
0
+8
+12
+18
+23
+29
+16
0
–8
–12
–18
–29
–11
–3
+1
+7
+12
+18
18
30
+41
+21
+12
+6
0
–14
0
+9
+15
+21
+28
+35
+20
0
–9
–15
–21
–35
–13
–4
+2
+8
+15
+22
30
50
+ 50
+25
+14
+7
0
–17
0
+11
+18
+25
+33
+42
+25
0
–11
–18
–25
–42
–16
–5
+2
+9
+17
+26
50
80
+60
+30
+18
+9
0
–21
0
+12
+21
+30
+39
+51
+30
0
–12
–21
–30
–51
–19
–7
+2
+11
+20
+32
80
120
+71
+35
+22
+10
0
–24
0
+13
+25
+35
+45
+59
+36
0
–13
–25
–35
–59
–22
–9
+3
+13
+23
+37
120
180
+83
+40
+26
+12
0
–28
0
+14
+28
+40
+52
+68
+43
0
–14
–28
–40
–68
–25
–11
+3
+15
+27
+43
180
250
+96
+46
+30
+13
0
–33
0
+16
+33
+46
+60
+79
+ 50
0
–16
–33
–46
–79
–29
–13
+4
+17
+31
+ 50
Diameter in mm
24
25
28
30
32
35
38
40
42
45
48
50
55
60
65
70
75
80
85
90
95
100
ISO tolerance zone
k6
m6
结束在毫米长度
50
60
80
110
140
170
210
受到推崇的
diameter ranges d
6
1)
表格DS
d
1
d
2
2)
d
3
d
4
d
5
t
1
t
2
t
3
t
4
t
5
over
to
+2
min.
+1
大约
大约
7
10
M3
2.5
3.2
5.3
5.8
9
12
2.6
1.8
0.2
表格DS(with thread) DIN 332/2
10
13
M4
3.3
4.3
6.7
7.4
10
14
3.2
2.1
0.3
13
16
M5
4.2
5.3
8.1
8.8
12.5
17
4
2.4
0.3
16
21
M6
5
6.4
9.6
10.5
16
21
5
2.8
0.4
21
24
M8
6.8
8.4
12.2
13.2
19
25
6
3.3
0.4
24
30
M10
8.5
10.5
14.9
16.3
22
30
7.5
3.8
0.6
30
38
M12
10.2
13
18.1
19.8
28
37
9.5
4.4
0.7
38
50
M16
14
17
23
25.3
36
45
12
5.2
1.0
50
85
M20
17.5
21
28.4
31.3
42
53
15
6.4
1.3
85
130
M24
21
25
34.2
38
50
63
18
8
1.6
130
225
M30
*)
26.5
31
40.2
44.6
60
77
22
8
1.9
225
320
M36
*)
32
37
49.7
55
74
93
22
11
2.3
320
500
M42
*)
37.5
43
60.3
66.6
84
105
26
15
2.7
*)
Dimensions not acc. to DIN 332 Part 2.
1)
Diameter refers to the finished workpiece.
2)
根据DIN 336第1部分的敲击孔钻直径。
Parallel keyway
G_MD10_EN_00198
t
2
d
6
d
2
d
3
d
4
d
5
60°
6,3
120°
d
1
t
1
t
3
t
4
t
5
©Siemens AG 2015