Rexnord gear couplings造型终身齿轮联轴器的三冠齿在根部，尖端和面上冠，以便自由地铰接并最大限度地减少由未对准引起的磨损。通过消除尖端装载，同时减少了反弹和径向间隙，终身的三冠齿可以帮助保护设备免受损坏的负载。
• 13 models for general purpose, high-speed and high-torque applications
•大型Flex Hubs在太空装置中容纳高扭矩应用
• 28 sizes
•高达43英寸（1,067毫米）的钻孔容量
• Up to 72,450,000 in-lb (8,185,763 Nm) torque capacity
• 3-year, heavy-duty warranty
The Falk Lifelign G20 Coupling is a double engagement, close-coupled solution with two flex halves to accommodate both offset and/or angular misalignment as well as end float. Engineered for all horizontal, close-coupled applications including fans, overhead cranes, conveyors, steel and paper mill equipment, it is adaptable with limited end float for use on electric motors, generators and other machinery fitted with sleeve or straight roller bearings.
Falk LifeLign G32标准法兰间隔耦合设计用于使用标准的双接合耦合和带有附加紧固件的标准双接合耦合和间隔管的泵和压缩机应用。用于快速交付的股票间隔长度可用流行尺寸。可以订购特殊长度。G32标准法兰套筒间隔件可以配置有或没有限量浮子。
Falk LifeLign型G52齿轮耦合是一种与浮动轴或三个轴承驱动列车一起使用的单个接合设计。以一个柔性的一半和一个刚性为特色，适用于容纳角度未对准。
The Falk Lifelign Type G62 Gear Couplings are double or single engagement brakewheel and disc brake couplings used for applications such as cranes, hoists, and conveyors among others. Brakewheel and disc brake couplings accommodate misalignment between connected equipment and eliminate the need for double shaft extensions on motors and gear drives for applications requiring brakes.
The Falk Lifelign Type G63 Gear Couplings are double or single engagement brakewheel and disc brake couplings used for applications such as cranes, hoists, and conveyors among others. Brakewheel and disc brake couplings accommodate misalignment between connected equipment and eliminate the need for double shaft extensions on motors and gear drives for applications requiring brakes.
The Falk Lifelign G70 Gear Coupling is a quick disconnect coupling suitable for low-speed applications including portable or stationary inching drive systems where the driving end hub/sleeve combination is mounted on the driving shaft or incher for connecting/disconnecting at standstill. When the long flex hub is mounted on the auxiliary shaft, the changeover is performed at standstill by engaging the free-running hub.
The Falk Lifelign G82 Couplings are rigid couplings used when there is no need to accommodate misalignment and where thrust loads are generated, such as vertical mixer applications. The coupling carries the torque load, weight of the shaft and impeller, thrust forces, and resulting bending movements.
Falk LifeRign GP20联轴器是双，单或刚性的啮合绝缘联轴器，用于消除从一个轴到另一个轴的杂散电流的流动并保护敏感电气设备。不设计用于高电流，短路或静电电荷的电气隔离。绝缘联轴器包括标准轮毂和套管，并利用缩小的直径插座头盖螺钉。
福尔克的Lifelign GV20耦合是一个垂直的两倍le engagement, close-coupled solution designed to accommodate the sleeve-centering assembly and suited for applications with inclinations over 10 degrees. Available in 12 sizes ranging from 1010G through 1070G the Lifelign GV20 couplings are engineered to accommodate torque loads up to 1,197,000 (lb-in) and shaft diameters up to 56.50 inches.
