躲闪
B17-34
SELECTION
特点与优势
Page B17-2
SPECIFICATION/HOW TO ORDER
Page B17-4
命名法
Page B17-5
选择/尺寸
PAGE B17-10
Plummer块
Sleeve Bearings
Slevoil
Take-Up Frames
Engineering
零件号索引
Keyword Index
袖子轴承 - bab和青铜色
General Information
SCOPE-for Stock Babbitted and Bronze Bushed Bearings,
Pillow Blocks and Take-Ups of the Rigid, Grease Lubricated
类型。
在相对页面上对表1的重要引用：表1评分
apply to the following DODGE Babbitted Sleeve Bearings:
Solid Journals
分裂的bab虫期刊
Rigid Babbitted Pillow Blocks
角度babbit枕头块
Plate Type Flange Bearings
Type H Take-Ups
A型和B型
表2的评分适用于道奇青铜衬套枕头块：
Split Bronze Bushed Journals
Rigid Bronze Bushed Pillow Blocks
角度青铜衬套枕头块
笔记
-Ratings do not apply to BRONZOIL, or SOLIDLUBE
枕头块。
巴布尔和青铜期刊轴承不包括
grease fittings.
Reference
-Flush type reducer bushings to be used with Part
数字
405015
1/8 NPT grease fitting:
To order 1/8 NPT grease fitting, confirm pipe tap dimension
在轴承尺寸页面上。如果管道水龙头为1/8，则频率
reducer bushing is not required. If the pipe tap is 1/4, 3/8 or 1/2;
订购适当的尺寸频率型还原衬套
到P/N 405015。
Part No.
Description
430081
1/2 x 1/8
430086
3/8 x 1/8
430087
1/4 x 1/8
选择
-Select a bearing from rating tables having a radial
负载等于或大于实际径向负载
满足了7到7的操作条件。
If these conditions cannot be met, select a bearing for an
Equivalent Radial Load to be obtained by multiplying the Actual
Radial Load by a service factor depending on the specific
应用。最多可用于2.0的百分比用于评分表中的区域
to the left of the zigzag line. Use a factor of up to 3.0 for areas to
曲折线的右侧。
负载评级基于建立的行业标准评级
由机械功率传输协会。（标准
第401号）
运行条件
1. Maintain adequate grease lubrication.
2.保持适当的轴承对准以均匀分布
在所有操作条件下加载。
3.正常运行载荷不得超过
负载表。起始和偶尔的峰值负载不应
exceed ratings by more than 100%.
4. Direction of load should not be closer than 30° to grease
groove or closer than 30° to the joint between cap and
根据。如果负载方向不在该区域内
建议，将最大负载降低50％。
5.轴日记帐表面的填充必须等于
commercial steel shafting (about 32 micro inches) and the
商业钢制式耐受性内的直径
(+.000 / -.002)
6. Ambient temperature should not exceed 130°F for babbitted
polymer limits and 300°F for bronze-bushed bearings. If the
轴从烤箱，轴等源传输热量
在轴承温度不应超过这些ambient
温度。
7.应保护轴承免受不良操作
条件。