DODGE
SELECTION
B7-7
Note:
Bearing analysis program “BEST” is available on www.ptwizard.com
FEATURES/BENEFITS
PAGE B7-3
HOW TO ORDER/NOMENCLATURE
PAGE B7-5
SELECTION/DIMENSIONS
PAGE B7-12
ACCESSORIES
PAGE B7-14
Eccentric Collar Ball
Bearing
Setscrew VSC Ball
Bearing
Eccentric SXV Collar
Ball Bearing
Take-Up Frames
Engineering
Part Number Index
Keyword Index
Eccentric Collar Ball Bearings
Recommended Torque
Setscrews
D-LOK
Mounting Bolts
Setscrew
大小
Key Hex
Across
Flats
◆
Recommended Torque
Cap
Screw
大小
Recom.
Torque
EZ-KLEEN
Recom.
Torque
金属外壳
EZ-KLEEN Housed Bearings
Standard Ball Bearing
Insert
Corrosion
Resistant
Stainless
Steel
Bolt Size
Recom.
Dry
Torque
(Grade 2)
2-Bolt PB,
2 & 4 Bolt
Fig. and Flg.
Brackets
Tapped Base PB
Min
Max
Bolt
大小
Torque
Bolt
大小
Torque
(in.)
(in.)
(in-lbs.)
(in.-lbs.)
(in.-lbs.)
(in.)
(in.-lbs.)
(in.-lbs.)
(in.)
(in.-lbs.)
(in.)
(in.-lbs.)
(in.)
(in.lbs.)
# 10
3/32
28
33
25
#8-32
58
46
3/8-16
240
3/8-16
225
3/8-16
175
1/4
1/8
66
80
60
# 10-32
90
72
7/16-14
384
7/16-14
350
7/16-14
350
5/16
5/32
126
156
117
1/4-28
180
144
1/2-13
600
1/2-13
500
1/2-13
400
3/8
3/16
228
275
206
5/16-24
400
320
5/8-11
1200
9/16-12
650
7/16
7/32
342
428
321
3/8-24
750
600
3/4-10
1950
5/8-11
1000
7/8-9
2890
(mm)
(mm)
(N-m)
(N-m)
(N-m)
(mm)
(N-m)
(N-m)
(mm)
(N-m)
(mm)
(N-m)
Torque for Austenitic
(18-8) Stainless
Max. torque values
published. Do not
exceed
M5
2.5
3.2
3.7
2.8
M4
585
4.68
M10
29
M8
15
M6
3
6.2
7.7
5.8
M5
10.75
8.6
M12
50
M10
25
M8
4
14.2
17.8
13.4
M6
20.5
16.4
M16
124
M12
50
M10
5
26
31
23
M8
45
36
M20
238
M14
75
M12
6
46
57
43
M22
322
M18
125
Lubrication
High Speed Operation - In the higher speed ranges, too much grease will cause over-heating. The amount of grease that the bearing
will take for a particular high speed application can only be determined by experience. If excess grease in the bearing causes
overheating, it will be necessary to remove grease fitting to permit excess grease to escape. The bearing has been greased at the
factory and is ready to run. When establishing a relubrication schedule, note that a small amount of grease at frequent intervals is
preferable to a large amount at infrequent intervals.
◆
NOTE:
Dodge does not recommend the use of oils or locking agents on setscrew threads. However, if utilized, the the minimum
installation torque values should be followed.
Lubrication Guide
Use a No. 2 Lithium complex base grease or equivalent*
Hours Run
per Day
Suggested Lubrication Period in Weeks
1
to 250
RPM
251
to 500
RPM
501
to 750
RPM
751
to 1000
RPM
1001
to 1500
RPM
1501
to 2000
RPM
2001
to 2500
RPM
2501
to 3000
RPM
8
12
12
10
7
5
4
3
2
16
12
7
5
4
2
2
1
1
24
10
5
3
2
1
1
1
1
* For EZ-KLEEN series bearings, use an aluminum complex base grease.
Lubrication recommendations are intended for standard products applied in general operating conditions. For modified products,
high temperature applications, and other anomalous applications contact product engineering at 864-284-5700.